IPG20 MK3Protezione intelligente per pompe

Progettato per impianti di irrigazione sia con acqua dolce sia con effluenti. Apprende la pressione di esercizio a ogni avvio dell’impianto, poi applica propri valori di soglia di sottopressione e sovrapressione per una rilevazione mirata di perdite e sovrapressioni. Adatto a settori fissi o irrigatori semoventi.

Pagina iniziale › Prodotti › Controllori per pompe › IPG20 MK3
IPG20 MK3

Caratteristiche

  • Apprende la pressione di esercizio
  • Impianti di irrigazione fissi o semoventi
  • Compensa le variazioni del terreno
  • Funzionamento ciclico per sistemi di irrigazione a settori
  • Rilevamento di perdite e ostruzioni
  • Protezione contro la perdita di flusso
  • Visualizza la pressione e i valori di soglia
  • Pressione nominale 20 bar / 2000 kPa
  • Funzionamento multitensione
  • Funzionamento manuale o automatico
  • Grado di protezione IP64

La protezione intelligente per pompe IPG20 MK3 è di costruzione termoplastica con attacco al processo da 1" BSP. Fornita con una paletta adatta a tubi da 25 mm e oltre, più due fili adatti a tubi con diametro interno da 65 mm – 100 mm (in funzione della velocità).

Selezioni il modello

Ordini — modelli disponibili

Codice modelloDescrizione
IPG20-MK3Standard model — 220–240 V AC and 24 V AC or 24 V DC operation
IPG20-12-MK3Low-voltage model — 12 V DC operation only

Limiti di funzionamento

Ambient temperature range1 °C to 50 °C
Liquid temperature range1 °C to 60 °C
Ingress protection ratingIP64
Maximum operating pressure (static or dynamic)20 bar / 2000 kPa
Minimum burst pressure> 30 bar / 3000 kPa
Starting pressure range0–2000 kPa in 1 kPa steps
Stopping pressure range0–2000 kPa in 1 kPa steps
Minimum pressure differential1 kPa
Recommended pipe size25 mm / 1" or larger (no upper limit)

Dati elettrici

Supply voltage220–250 V AC or 18–25 V AC/DC (multi-voltage input)
Maximum motor loadSingle-phase motors up to 2.4 kW max at 240 V AC (P1). 3-phase motors of all sizes via a suitable interposing contactor — no maximum motor size applies.
Relay 1 contact rating16 A at 240 V AC resistive
Relay 2 contact rating16 A at 240 V AC resistive

Funzioni

# = impostabile dall’utente

#Manual or Automatic operation—
#Auto terrain compensationAllows for contour change with a travelling irrigator.
#Drift allowance (kPa)Auto terrain compensation only.
#Pre-start delay timerAdjustable from 1 second to 27.7 hours in 1-second increments.
#Use alarm relay—
#Absolute low pressureDetects a major leak during start-up.
#Low pressure marginFine leak detection.
#Absolute high pressureClosed-valve protection.
#High pressure marginPartial blockage detection.
#Set-point marginAllowable pressure variation during the learning process.
#Ramp-up timerAllows time to establish stable pressure. 1 second to 15 minutes in 1-second increments.
#Set-point timerAdjustable in 60-second increments.
#Pressure dip timerAdjustable from 1 second to 4 minutes in 1-second increments.
#Pressure spike timer—
#Run-on timer (loss of flow)Adjustable from 1 second to 15 minutes in 1-second increments.
#Cyclic runningRunning and stopping times both 2 minutes to 99 hours 59 minutes in 1-minute increments. Not available in auto-terrain-compensation mode.
#Auto restart on a faultAdjustable 1 minute to 99 hours 59 minutes. Not available in auto-terrain-compensation mode.
#Program lock—
Pressure / set-point displayDisplays system pressure and high & low pressure set points in kPa.
Pump run-time displayDisplays the total time the pump ran in minutes.
Fault diagnostic displayDisplays the reason for stopping on a fault.
Remote learningInstigate the learning process using a remote switch (manual operation).
No-flow protectionNo-flow protection at all times.

Dimensioni

Dimensioni di IPG20 MK3
Three views with key dimensions (mm). 1" BSPT thread connection; paddle is cut to suit application; three M20 cable glands; removable protective cap.

Self-Learning Pressure Algorithm

The IPG20 MK3 measures the system’s normal operating pressure each time it starts and uses that as the reference for under- and over-pressure detection. As the irrigator travels over varying terrain the auto-terrain-compensation function adjusts the reference downward / upward in real time, so leak and blockage thresholds remain meaningful even as system pressure changes naturally.

Flow Sensitivity & Paddle Trimming

The IPG20 ships with one paddle (suits pipes 25 mm and larger) and two trailing wires (suits 65–100 mm ID, subject to velocity). The flow at which the paddle activates depends on pipe size, viscosity, and trimmed paddle length. Use the online Paddle Calculator to estimate activation flow and determine how much to trim the paddle for your application.

Open the Paddle Calculator →

3-Phase Pump Motors

The IPG20 MK3 can be used to control either single-phase or 3-phase pumps, provided a 220–240 V AC or 24 V AC/DC supply is available at the installation site. For 3-phase motors the IPG20 drives an interposing contactor — use the Pump Controller Power Calculator to size the contactor and verify cable rating + voltage drop.

Open the Pump Controller Power Calculator →

Application Restriction

The IPG20 MK3 is an industrial control device, specifically designed for use in dairy and agricultural applications. It must never be used for any other application. Installation must be carried out by a qualified pump engineer, and all electrical work by a licensed electrician.

Hazardous Areas

The IPG20 MK3 is not certified for use in hazardous areas and must not be installed in any area classified as hazardous under AS/NZS 60079.10 (Zone 0, 1, 2, 20, 21 or 22).

Manutenibilità

La protezione intelligente per pompe IPG20 MK3 non è riparabile dall’utente. Sono comunque disponibili ricambi presso Kelco Engineering o il Suo distributore.

Altri prodotti in Controllori per pompe

E30 MK2

E30 MK2

Controllore digitale di pressione

F29 MK3

F29 MK3

Flussostati programmabili

F60 MK3

F60 MK3

Controllore digitale per pompe