Seri C25Sakelar Aliran Inline (1")

Versi yang lebih besar dari C15: sakelar bodi kuningan 1" BSPT/NPT untuk aplikasi aliran sedang. Serbaguna, digerakkan secara magnetik, normally-off; menyala sebagai respons terhadap aliran. Ideal untuk aplikasi cairan bersih, termasuk peningkatan tekanan (pressure boosting) dan pengendalian pompa atau kipas melalui relai, kontaktor, atau PLC, pada air tawar dan bahan bakar diesel.

Seri C25

Fitur

  • Bodi kuningan satu bagian
  • Dapat dipasang pada semua posisi
  • Tersedia model yang sesuai untuk diesel dan oli
  • Kontak sakelar reed kering
  • Mendeteksi aliran yang sangat rendah: aktif pada 0.28 L/min (vertikal, penahan non-magnetik)
  • Kehilangan head yang sangat rendah
  • Sepenuhnya dapat diservis
  • Tahan cuaca

Seri C25 dibangun berdasarkan desain displaced-piston terbukti yang sama dengan C15, tetapi dengan inlet/outlet 1" untuk laju aliran lebih tinggi (hingga 100 L/min). Modul listrik tertutup mengapit bodi kuningan satu bagian dan dapat diservis sepenuhnya: mudah dilepas tanpa mengganggu pipa dan dapat diputar atau dibalik secara independen dari bodi. Di dalam bodi, piston yang terpasang bebas dan tersuspensi secara magnetik menggerakkan sakelar begitu aliran dimulai. C25 dipasok dengan kontak sakelar reed kering untuk pengendalian relai atau PLC. Penahan piston non-magnetik (disertakan) membuat sakelar sekitar 6 kali lebih sensitif bila dipasang vertikal dengan aliran ke atas.

Informasi Lainnya

Lembar data lokal belum tersedia untuk produk ini dalam bahasa yang Anda pilih. Tautan di bawah membuka versi bahasa Inggris.

Pilih Model

Pemesanan: Model yang Tersedia

Nomor ModelDeskripsi
C25-BDry reed switch S.P.S.T. N.O. — 50 W/VA, 250 VAC / 200 VDC, 1.5 A max. Suitable for PLC, telemetry and logic circuits.
C25-B-DDiesel-suited dry reed switch S.P.S.T. N.O. — 50 W/VA, 250 VAC / 200 VDC, 1.5 A max. Suitable for PLC, telemetry and logic circuits.

Batas Operasi

Switching point on rising flow (horizontal or vertical, magnetic retainer fitted)1.6 L/min (water at ambient)
Switching point on falling flow (horizontal or vertical, magnetic retainer fitted)1.3 L/min (water at ambient)
Switching point on rising flow (vertical, flow upward, non-magnetic retainer fitted)0.28 L/min (water at ambient)
Switching point on falling flow (vertical, flow upward, non-magnetic retainer fitted)0.20 L/min (water at ambient)
Maximum recommended flow rate through switch100 L/min
Maximum operating pressure (static or dynamic)100 bar / 1450 psi
Operating temperature rangeHot or cold liquids from −20 °C up to 90 °C continuous; can be steam-sterilised at 100 °C for short periods
Ingress protection ratingIP56

Data Listrik

Module typeDry-contact reed switch (electrical module B)
Contact configurationS.P.S.T. normally open
Switched power (maximum)50 W/VA
Switched voltage (maximum)250 VAC / 200 VDC
Switched current, resistive AC RMS (maximum)1.5 A
Inductive loads (power factor 0.4)Not suitable
Rating0 to 250 VAC / 200 VDC at 50 W/VA maximum switched power
Typical applicationPLC, telemetry and relay logic circuits

Dimensi

Dimensi Seri C25
Multi-view overall dimensions in millimetres — 108 mm body length, 41 mm A/F brass hex, 1" BSPT or NPT thread, 57 mm end-view width, electrical module 56 mm above and 24 mm below the pipe centreline, 8.5 mm cable gland.

Switching-Point Sensitivity

Switching point and sensitivity to flow depend on orientation, liquid velocity, viscosity and piston clearance. With the switch mounted vertically and flow passing upward, fitting the supplied non-magnetic piston retainer makes the C25 approximately 6 times more sensitive (drops switch-on flow from 1.6 L/min to 0.28 L/min). For this the switch must be mounted vertically with the flow switch entry facing downwards, and the piston and retaining components can be changed by removing the stainless steel circlip with long-nose pliers. Switching points are for water at ambient temperature: increasing fluid viscosity decreases the flow rate required to actuate the switch, and decreasing it proportionally increases the switch-on flow rate.

Hazardous Areas

The C25-B and C25-B-D are simple apparatus under AS/NZS 60079.11 and may be used in a hazardous area only as part of an intrinsically safe circuit, connected through suitably certified associated apparatus. They are not Ex certified in their own right. The full conditions of use are given in the installation sheet.

Compatible Liquids and Iron

Suits many clean liquids, including fresh water and diesel fuel. This flow switch operates magnetically and is therefore not suited to any application where iron or iron scale may be present in the process liquid. Where scale or entrained material may be present, always install a Y-strainer in the inlet pipe directly before the switch.

Installation

Install in any location in vertical or horizontal pipes; in vertical pipes flow can be upward or downward with very little difference in flow sensitivity. Where possible, fit a union on the inlet and outlet for easy removal for cleaning or servicing, and orient the switch correctly to the direction of flow — the male threaded end is the inlet. Make sure no thread tape or other material enters the switch. The electrical module can be removed or loosened (undo the 4 self-tapping screws and the sealed module lifts off) so the body can be screwed into tight locations, for example the discharge port of a pump.

Check Valves

Many applications benefit from a non-return valve in the pipework directly before the switch. The flow switch is not designed to operate as a one-way valve, and rapid or high pressure flow reversal, such as water hammer, can damage its piston.

Electrical Safety

The C25 Series flow switch is a mains voltage device. All electrical work must be performed by a fully qualified and licensed electrician and conform to AS/NZS (or equivalent) standards and local wiring rules. After installing or servicing, always replace the lid, fully tighten the lid screw and ensure the cable gland is fully tightened. Without its lid the switch is not weather or insect proof and presents a potential shock hazard.

Kemudahan Servis

Sepenuhnya dapat diservis di lapangan. Modul listrik mudah dilepas tanpa mengganggu pipa (lepaskan 4 sekrup self-tapping yang mengikat kedua bagian modul; modul tertutup kemudian dapat diangkat) dan dapat diputar atau dibalik secara independen dari bodi. Piston harus terpasang bebas dan kembali ke posisi mati begitu aliran berhenti; jika macet, lepaskan circlip pegas pada port outlet dengan tang hidung panjang, lalu bersihkan piston dan spider magnetik bersirip tiganya, serta periksa adanya kerak besi. C25-B dapat diuji dengan penguji kontinuitas: awalnya mati, dan hidup ketika piston didorong mundur. Modul cadangan dan kit seal tersedia dari Kelco Engineering atau distributor Anda.

Lainnya di Sakelar aliran inline