Seri TWSakelar Aliran Tipe Kawat (Trailing Wire)

Menggunakan sensor kawat baja tahan karat yang fleksibel sebagai ganti paddle untuk mendeteksi aliran. Cocok untuk aplikasi pembuangan terbuka dan pipa 50 mm (2") ke atas. Ideal bila terdapat padatan atau semi-padatan: pemompaan limbah, slurry, pertambangan, dan pemompaan normal berkecepatan tinggi di mana paddle mudah terkotori atau mengalami kelelahan material.

Seri TW

Fitur

  • Sensor kawat (trailing wire) unik, tanpa paddle yang dapat terkotori atau tersangkut
  • Sakelar S.P.D.T. standar 5 hingga 500 V AC, 15 A (TW-H)
  • Tersedia model kontak emas tegangan rendah (TW-L)
  • Tersedia model 1" BSP atau NPT
  • Model baja tahan karat 316 atau polipropilena
  • Panjang kawat (trailing wire) 50 hingga 300 mm (2" hingga 12")
  • Mudah diservis
  • Tersedia model bertekanan nominal 400 bar / 5800 psi (baja tahan karat)
  • Override manual terpasang pada semua model
  • Penggerak magnetik tanpa seal
  • Sensitivitas dapat diatur
  • Tahan cuaca IP67

Sensor tipe kawat (trailing wire) melentur mengikuti aliran, bukan melawannya, sehingga tahan terhadap padatan terbawa, serat, dan kecepatan tinggi yang dapat merusak paddle. Sensor kawat baja tahan karat yang fleksibel ini menawarkan keunggulan besar dibandingkan paddle konvensional ketika terdapat padatan atau semi-padatan, misalnya pada pemompaan air limbah, dan juga cocok untuk aplikasi lumpur cair (slurry) dan pertambangan serta banyak situasi pemompaan biasa di mana kecepatan aliran tinggi dan sakelar tipe paddle tidak cocok. Dipasok dengan sambungan proses polipropilena atau baja tahan karat 316 dalam 1" BSP atau NPT. Model standar TW-H menggunakan sakelar mikro S.P.D.T. dengan rating 5 hingga 500 V AC, 15 A; model tegangan rendah TW-L menggunakan sakelar mikro kontak emas S.P.D.T. untuk sinyal dengan arus pembasahan rendah seperti input PLC dan telemetri. Model sakelar reed TW-RL yang lebih lama sudah dihentikan dan digantikan oleh TW-L. Override manual terpasang pada semua model Seri TW.

Informasi Lainnya

Lembar data lokal belum tersedia untuk produk ini dalam bahasa yang Anda pilih. Tautan di bawah membuka versi bahasa Inggris.

Tipe sakelar
Ulir / sambungan
Bagian yang terkena cairan
Panjang kawat (mm)
Ketuk sebuah panjang untuk memilih model tersebut.

Cara kawat (trailing wire) Seri TW merespons aliran

Memuat model 3D…

Tanpa aliran: kawat baja tahan karat 2 mm menggantung diam.

Pemesanan: Model yang Tersedia

Nomor ModelDeskripsi
TW-H-25B-50 … TW-H-25B-300Standard SPDT, 1" BSP, all polypropylene wetted parts
TW-H-25N-50 … TW-H-25N-300Standard SPDT, 1" NPT, all polypropylene wetted parts
TW-H-25B-SS-50 … TW-H-25B-SS-300Standard SPDT, 1" BSP, 316 stainless process connection (high-pressure model)
TW-H-25N-SS-50 … TW-H-25N-SS-300Standard SPDT, 1" NPT, 316 stainless process connection
TW-L-25B-50 … TW-L-25B-300Low-voltage gold-contact model (L) — S.P.D.T. gold-contact micro-switch, 1" BSP, all polypropylene wetted parts
TW-L-25N-50 … TW-L-25N-300Low-voltage gold-contact model (L) — S.P.D.T. gold-contact micro-switch, 1" NPT, all polypropylene wetted parts
TW-L-25B-SS-50 … TW-L-25B-SS-300Low-voltage gold-contact model (L) — S.P.D.T. gold-contact micro-switch, 1" BSP, 316 stainless process connection (high-pressure model)
TW-L-25N-SS-50 … TW-L-25N-SS-300Low-voltage gold-contact model (L) — S.P.D.T. gold-contact micro-switch, 1" NPT, 316 stainless process connection

Batas Operasi

Maximum operating pressure (all-polypropylene model, static or dynamic, ambient)18 bar / 261 psi
Pressure de-rating (all-polypropylene model)Maximum operating pressure must be de-rated linearly as operating temperature increases, so that at 60 °C / 140 °F it does not exceed 1 bar / 15 psi absolute
Maximum operating pressure (stainless model, static or dynamic, ambient)400 bar / 5800 psi
Minimum burst pressure (all-polypropylene model, ambient)45 bar / 652 psi
Minimum burst pressure (stainless model, ambient)500 bar / 7215 psi
Maximum operating temperature (polypropylene)60 °C / 140 °F (see pressure de-rating)
Maximum operating temperature (stainless)80 °C / 176 °F
Minimum operating temperature-20 °C / -4 °F
Ingress protection ratingIP67

Data Listrik

TW-H switch typeS.P.D.T. (single pole, double throw) microswitch for general control circuits from 5 to 500 V AC — ideal for pump starters, relay logic, contactors and timers. Minimum load 160 mA at 5 V DC.
TW-H direct motor controlDirectly switches pump motors up to ¼ HP (approx. 185 W) at 240 V AC. For larger motors use a contactor or relay.
TW-H absolute limits500 V AC and 15 A maximum (10 A at 500 V AC); 5 V DC and 160 mA minimum. Maximum voltage and maximum current cannot be applied together — use the load ratings below for the limit at each voltage and load type.
TW-H load ratings at 125 V ACResistive 15 A (NC/NO) · Lamp 3 A (NC), 1.5 A (NO) · Inductive 15 A (NC/NO) · Motor 5 A (NC), 2.5 A (NO)
TW-H load ratings at 250 V ACResistive 15 A (NC/NO) · Lamp 2.5 A (NC), 1.25 A (NO) · Inductive 15 A (NC/NO) · Motor 3 A (NC), 1.5 A (NO)
TW-H load ratings at 500 V ACResistive 10 A (NC/NO) · Lamp 1.5 A (NC), 0.75 A (NO) · Inductive 6 A (NC/NO) · Motor 1.5 A (NC), 0.75 A (NO)
TW-H load ratings at 8 V DCResistive 15 A (NC/NO) · Lamp 3 A (NC), 1.5 A (NO) · Inductive 15 A (NC/NO) · Motor 5 A (NC), 2.5 A (NO)
TW-H load ratings at 14 V DCResistive 15 A (NC/NO) · Lamp 3 A (NC), 1.5 A (NO) · Inductive 10 A (NC/NO) · Motor 5 A (NC), 2.5 A (NO)
TW-H load ratings at 30 V DCResistive 6 A (NC/NO) · Lamp 3 A (NC), 1.5 A (NO) · Inductive 5 A (NC/NO) · Motor 5 A (NC), 2.5 A (NO)
TW-H load ratings at 125 V DCResistive 0.5 A (NC/NO) · Lamp 0.5 A (NC), 0.5 A (NO) · Inductive 0.05 A (NC/NO) · Motor 0.05 A (NC), 0.05 A (NO)
TW-H load ratings at 250 V DCResistive 0.25 A (NC/NO) · Lamp 0.25 A (NC), 0.25 A (NO) · Inductive 0.03 A (NC/NO) · Motor 0.03 A (NC), 0.03 A (NO)
TW-L switch typeGold contact microswitch, S.P.D.T., gold alloy contacts, so it switches reliably at the low wetting currents of PLC inputs, telemetry and relay logic. Not suitable for inductive or capacitive loads such as contactors and relays. Loads above the rating will damage the switch.
TW-L rated current (resistive)0.1 A at 125 VAC; 0.1 A at 8, 14 and 30 VDC
TW-L inrush current0.1 A maximum (NC and NO)
TW-L minimum applicable load1 mA at 5 VDC
TW-L operating range (micro load)5 to 30 V, 5 to 800 mW (26 mA maximum at 30 V)
TW-L contact resistance50 mΩ maximum (initial)
TW-L typical applicationsPLC, telemetry and low voltage control

Dimensi

Dimensi Seri TW
Insertion trailing-wire switch — same housing as F Series, with a flexible stainless wire instead of a rigid paddle. Overall dimensions: 100 mm × 45 mm, 88 mm high above a 24 mm thread; M20 cable gland. 1" BSP or NPT thread; 316 stainless steel trailing wire, 2 mm diameter. Wire lengths 50–300 mm; specify the length when ordering.

Warning: Electrical Safety

The TW Series is a mains voltage device - incorrect installation can cause death or serious injury. All electrical work must be carried out by a licensed electrician.

Wire Length & Flow Sensitivity

The flow rate required to actuate the switch depends on many variables such as turbulence, liquid viscosity and the exact surface area of sensor wire exposed to the flow. The wire is made in fixed lengths of 50, 80, 100, 140, 160, 180, 200, 250 or 300 mm (2" to 12"), measured from the tip of the wire to the bottom end face of the process connection, and the required length must be specified when ordering (e.g. TW-H-25B-SS-100). Use the online Paddle Trimming Calculator to find the optimum wire length: enter your pipe inside diameter, flow rate and liquid to check the switch will operate reliably at your flow.

Open the Paddle Calculator →

Installation & Mounting

Mount in a pipe tee, tapping saddle or weld-on socket. For effluent or liquids carrying solids, use a stand-off tee (80 or 100 N/B) so the switch body sits out of the line of flow; the arrow on the switch must point in the direction of flow. The switch can go in suction or delivery pipework, horizontal or vertical. In vertical pipe, flow must be upward. Do not mount on the underside of horizontal pipe. Where possible, mount the switch away from pumps, valves and bends: a fitting directly upstream makes the flow uneven and turbulent at the wire sensor, which can shift the switching point slightly or make the wire flutter near the switching point, while downstream fittings have little effect. If the switch has to go close to a fitting, enter the upstream straight length in the Paddle Trimming Calculator and check operation on commissioning. Seal the thread with PTFE tape or thread sealant, leaving at least 4 mm of thread above the socket, and tighten with a spanner on the spanner flats only — never twist the switch body.

Adjusting Sensitivity

Switches are supplied at maximum sensitivity (adjuster wound fully in). To decrease sensitivity, remove the red dust cap and wind the adjusting screw out (anti-clockwise) with a wide flat screwdriver. The further out the screw, the more flow is needed to operate the switch. Refit the dust cap.

Manual Override

A manual override is built into all TW Series models (TW-H and TW-L). Pressing the button lets the system be started manually at any time, and makes testing and commissioning very simple. To test after wiring, press the red manual override button under the cable gland — the switch changes state as if liquid were pushing the wire.

Hazardous Areas

The TW-H is not certified for use in hazardous areas and must not be installed in any area classified as hazardous under AS/NZS 60079.10 (Zone 0, 1, 2, 20, 21 or 22). The TW-L is simple apparatus under AS/NZS 60079.11 and may be used in a hazardous area only as part of an intrinsically safe circuit, connected through suitably certified associated apparatus. It is not Ex certified in its own right. The associated apparatus must not exceed Uo ≤ 30 V, Io ≤ 100 mA. The full conditions of use are given in the installation sheet.

When to use a Wire vs a Paddle

Choose a trailing-wire sensor when: (a) solids or semi-solids are present, or the fluid carries fibres or stringy debris that would foul a paddle (sewage pumping, slurry and mining applications); (b) the flow velocity is high and a conventional paddle-type switch is unsuitable (typical above 4 m/s in larger pipes); (c) you are sensing flow in open discharge applications or in pipes from 50 mm (2") upwards, including pipes too large for a standard paddle (the TW handles 50 mm and up). For clean-water, low-velocity applications a paddle (F Series / FM Series) is usually more sensitive.

Approved Standards

The 'H' and 'L' microswitches used in the TW Series are approved to UL1054 (File E41515), CSA C22.2 No.55 (File LR21642) and EN61058-1, and are CE marked.

Kemudahan Servis

Mudah diservis dan sepenuhnya dapat diservis di lapangan. Seri TW sangat mudah diservis, dan sebagian besar komponen tersedia dalam kit suku cadang; suku cadang tersedia dari pemasok Anda. Enklosur listrik dilepas dari bagian basah (wet-end) dengan satu sekrup tanpa mengganggu pipa. Kawat, seal, dan sakelar pengganti tersedia dari Kelco Engineering atau distributor Anda.

Lainnya di Sakelar aliran tipe kawat