Seri UB25Sakelar Aliran Inline: Bodi Baja Tahan Karat 316 Padat

Sakelar piston yang digerakkan secara magnetik dengan bodi baja tahan karat 316 hasil permesinan padat: tekanan nominal 200 bar, menangani cairan hingga 90 °C. Ideal untuk peningkatan tekanan air panas/dingin (pressure boosting), sistem air panas gravitasi, shower keselamatan, dan aplikasi berkeandalan tinggi lainnya.

Seri UB25

Fitur

  • Cocok untuk pipa 25 NB (1 inci)
  • Pemasangan semua posisi yang serbaguna
  • Tekanan nominal 200 bar / 2900 psi
  • Beroperasi pada aliran yang sangat rendah
  • Bodi tahan cuaca IP67
  • Bodi logam baja tahan karat 316 hasil permesinan padat
  • Kapasitas aliran lewat yang tinggi
  • Menangani cairan hingga 90 °C
  • Titik penyakelaran 1.5 L/min pada aliran yang naik perlahan sesuai pasokan (0.23 L/min dengan penahan piston non-magnetik)

Bodi UB25 dimesin dari baja tahan karat 316 padat. Di dalamnya, piston yang meluncur bebas (polipropilena berpenguat kaca; nilon pada model Dieseline -D) didorong mundur oleh aliran hingga cairan melewatinya. Piston menggerakkan sakelar berkopling magnetik dan didorong kembali ke posisi mati oleh tolakan magnetik saat aliran berhenti: tidak ada pegas di area basah. Piston dan enklosur listrik terbuat dari polipropilena berpenguat kaca. Inlet jantan BSPT 25 mm (1") dan outlet betina BSPT 1"; tersedia tiga modul listrik, ditambah model Dieseline -D.

Informasi Lainnya

Pilih Model

Pemesanan: Model yang Tersedia

Nomor ModelDeskripsi
UB25-BDry reed switch S.P.S.T. N.O. — 50 W, 250 V AC / 200 V DC, 1.5 A max. Not suitable for inductive loads. PLC and general control circuits.
UB25-CDry reed switch S.P.D.T. break before make — 20 W, 140 V AC / 150 V DC, 1 A max. Not suitable for inductive loads. PLC control and safety showers.
UB25-RSolid state relay S.P.S.T. N.O. — 740 W, 12 to 240 V AC, 4 A continuous (spike to 15 A); inductive loads 4 A at 240 V AC. AC control circuits and AC motor control.
UB25-B-DDieseline model — nylon piston in place of the glass reinforced polypropylene piston; otherwise as UB25-B.
UB25-C-DDieseline model — nylon piston in place of the glass reinforced polypropylene piston; otherwise as UB25-C.
UB25-R-DDieseline model — nylon piston in place of the glass reinforced polypropylene piston; otherwise as UB25-R.

Batas Operasi

Maximum recommended operating pressure (static or dynamic)200 bar / 2900 psi
Minimum burst pressure400 bar / 5800 psi
Maximum liquid temperature90 °C
Minimum liquid temperature-20 °C
Maximum recommended continuous flow (water)100 L/min
Switching point on a slowly rising flow (±15%)1.5 L/min as supplied (standard magnetic piston retainer); 0.23 L/min with the non-magnetic piston retainer fitted
Switching point on a slowly falling flow (±15%)1.2 L/min as supplied (standard magnetic piston retainer); 0.18 L/min with the non-magnetic piston retainer fitted
Minimum gravity head required to actuate the switch1.5 metres
Switching point sensitivityStandard magnetic piston retainer fitted as supplied. A non-magnetic piston retainer is also supplied with each switch; fitted vertically with upward flow, it lowers the flow rate needed to actuate the switch by approximately 6.5 times.
Process connection25 mm (1") BSPT male inlet, 1" BSPT female outlet
Ingress protection ratingIP67

Dimensi

Dimensi Seri UB25
Compact inline mount — 73 mm tall × 50 mm housing × 105 mm overall body length. 25 mm (1") BSP male inlet to 1" BSP female outlet. 20 mm cable gland. Solid 316 stainless steel body.

Warning: Electrical Safety

The UB25 Series flow switch is a mains voltage device. Death or serious injury may result if this switch is not correctly installed and operated. All electrical work on this switch must be performed by a fully qualified and licensed electrician.

Two Piston Retainers Supplied

The UB25 is supplied as standard with a magnetic piston retainer that allows the switch to be oriented in any required position in pipework; in vertical pipework flow can be either upward or downward through the switch. A non-magnetic piston retainer is also supplied with each switch — when this is fitted, the switch must be oriented vertically with flow passing upward through its body, and the flow rate required to actuate the switch is approximately 6.5 times lower (0.23 L/min rising and 0.18 L/min falling, ±15%, against 1.5 and 1.2 L/min as supplied). It is commonly used to enhance the sensitivity of the switch in gravity head applications such as boosting water pressure in gravity fed hot water systems.

Dieseline Model (-D)

Order the -D suffix (e.g. UB25-B-D) for the Dieseline model. The piston is glass reinforced polypropylene on standard models and nylon on Dieseline -D models. The solid 316 stainless steel body is suitable for neutral liquids such as hot or cold water, or oils.

Mounting & Pump Installation

The UB25 can be mounted in any orientation in the pipework, including upside down, in horizontal or vertical pipework. There is a direction of flow arrow on the electrical enclosure; the switch will not operate against a reversed flow. Pipework can be used to support the switch, or it can be screwed directly into valve manifolds or pump ports — use thread tape or sealant. Do not use this flow switch as a non-return valve. In the typical pressure boosting installation the switch is fitted to the pump discharge, with a Y strainer on the pump inlet and a non-return valve downstream of the flow switch.

Clean Fluid & Line Filtration

The UB25 contains a close fitting piston and should only be used where the process fluid is reasonably clean and free of entrained or suspended material. It should not be used with fluids containing large particulate matter, ferrous materials or fibrous matter. If the degree of contamination of the process fluid can’t be guaranteed, fit suitable line filtration to the system.

Servicing the Piston

To service the piston or to install the non-magnetic piston retainer, use long nosed pliers to remove the spring circlip in the outlet port of the switch. Press the piston back with your finger; it should pop out along with its three finned magnetic retainer. Ensure there are no pieces of iron scale adhered to the piston or retainer and that both parts are free of damage. Reassemble the switch and test it to ensure the piston is a free and smooth fit.

Typical Applications

Hot and cold water pressure boosting, gravity hot water system control, hot water circulation actuation, safety shower alarm sentinel, wash down pump control, solar hot water control, mains pressure boosting and constant pressure pump control.

Hazardous Areas

The UB25-B and UB25-C (including -D models) are simple apparatus under AS/NZS 60079.11 and may be used in a hazardous area only as part of an intrinsically safe circuit, connected through suitably certified associated apparatus. They are not Ex certified in their own right. The full conditions of use are given in the installation sheet. The UB25-R and UB25-R-D are not certified for use in hazardous areas and must not be installed in any area classified as hazardous under AS/NZS 60079.10 (Zone 0, 1, 2, 20, 21 or 22).

Kemudahan Servis

Sepenuhnya dapat diservis di lapangan. Untuk menservis piston, lepaskan circlip pegas pada port outlet; sebagian besar komponen sakelar tersedia dalam kit suku cadang. Modul listrik dapat diulir lepas dari bodi baja tahan karat tanpa mengganggu pipa. Piston cadangan (varian air dan dieseline), seal, dan modul listrik tersedia dari Kelco Engineering atau distributor Anda.

Lainnya di Sakelar aliran inline