Seri KPSakelar Level Probe (Pelampung Vertikal)
Sakelar pelampung ringkas bergaya probe berorientasi vertikal. Bodi luar berdiameter 25 mm muat pada pipa atau sumur bor 25.4 mm. Bodi UPVC berventilasi dengan pelampung polipropilena di dalamnya. Pengulangan penyakelaran ±1 mm; ideal sebagai alternatif probe konduktivitas pada pompa submersible sumur bor.

Fitur
- Tanpa bagian bergerak di luar
- Konstruksi padat yang andal
- Sakelar reed tiga kawat S.P.D.T.
- Konstruksi PVC, polipropilena & fluorosilikon
- Aksi penyakelaran yang stabil dan berulang
- Tanpa komponen merkuri atau timbal
- Ringkas, diameter 25 mm, muat pada pipa / sumur bor 25.4 mm
- Keterulangan penyakelaran ±1 mm
- Kedalaman rendam maksimum 45 m (tekanan statis 450 kPa)
- pH 1–14, bagian yang terkena cairan dari UPVC dan polipropilena
- Tersedia pemberat kabel opsional
Sakelar level probe KP terdiri dari bodi UPVC berventilasi yang berisi pelampung polipropilena. Kenaikan permukaan cairan mengangkat pelampung dan mengaktifkan sakelar reed berkopling magnetik di dalam kepala sakelar; penurunan permukaan membuat pelampung turun dan sakelar reed berhenti aktif. Kepala sensor sakelar dimesin CNC dari UPVC padat dan di-potting sepenuhnya. Sakelar ini adalah sakelar reed kontak kering single pole double throw yang sangat lentur, yang dapat memutus-sambung hingga 140 VAC atau 150 VDC pada arus hingga 0.25 A beban resistif, dengan maksimum 5 Watt / VA. Sakelar ini tidak cocok untuk digunakan pada tegangan jala-jala: ini adalah perangkat sinyal tegangan rendah untuk input BMS dan PLC, serta alternatif bagi probe konduktivitas pada instalasi pompa sumur bor submersible. Harus dipasang secara vertikal dengan kabel di bagian atas.
Informasi Lainnya
Lembar data lokal belum tersedia untuk produk ini dalam bahasa yang Anda pilih. Tautan di bawah membuka versi bahasa Inggris.
Pilih Model
Pemesanan: Model yang Tersedia
Batas Operasi
Data Listrik
Dimensi

Typical Applications
Deep-well bore-pump protection (borehole installations); saline-water service; withstands most common chemicals; chemical-tank monitoring; bilge-level control; high & low level alarms; intrinsically safe circuits (simple apparatus); general-purpose liquid-level sensing.
Hazardous Areas
The KP is simple apparatus under AS/NZS 60079.11 and may be used in a hazardous area only as part of an intrinsically safe circuit, connected through suitably certified associated apparatus. It is not Ex certified in its own right. The full conditions of use are given in the installation sheet.
Safety — Low Voltage Only
The KP probe level switch is not suitable for use at mains voltage and must never be used in mains voltage applications. It is a low voltage signalling device for low voltage, low current applications only, and is ideal as an input device for BMS and PLC applications. Its reed switch suits low wetting current, low voltage control such as PLC and BMS control at 24 V, 3.3 V and 5 V, signalling and telemetry, and relay logic circuits. It is not suitable for switching inductive loads such as high wattage relays, motors of any kind or contactors. The contact power rating is the product of switching voltage and current and must never exceed 5 Watts / VA.
Mounting — vertical only
The KP probe MUST be installed vertically (within 5 degrees of vertical) with its cable at the top. It will not operate in any other orientation. It does not need to float or tilt to operate; its float is contained within the vented UPVC housing. Four mounting methods: (A) a rigid probe assembly made from 15 NB PVC pressure pipe and a PVC socket, fixed to a wall with the 15 NB pipe saddles supplied with the switch; (B) strapped to suitable pipework with standard cable ties, using the locating trenches in the KP body; (C) suspended vertically in a pit or tank, with a Kelco KCW cable weight fitted to the cable to hold the switch in place if required; (D) bolted to the side wall of a pit or tank using the 15 NB wall clips provided with the switch. The 15 NB probe assembly protects the cable from mechanical and chemical damage. Avoid violent turbulence and any place where the switch or cable can abrade against adjacent objects.
Magnet — Ferric and Iron Particles
The KP probe switch contains a magnet. Do not use it in applications involving ferric solutions such as ferric chloride, or liquids containing suspended iron particulates: iron sludge may agglomerate around the magnet and prevent the free movement of the float.
Cable Data
S05RN-F 3 × 0.75 mm² cable: black CPE (chlorinated polyethylene) outer sheath, fluorosilicone cable boot, EPR insulation, 3 × 24/0.2 mm plain copper (0.75 mm²), 7.0 ± 0.2 mm diameter, core colours blue (common), black (normally closed) and brown (normally open), voltage rating 300 / 500 V, test voltage 2000 V / 2500 V, minimum bending radius 6 × overall diameter (42 mm), conductor operating temperature -30 °C to +60 °C (85 °C max), CENELEC HD 22.4 S4 & VDE 0282-4/2005, conductor resistance 26.7 Ω/km max per core (20 °C), cable current rating 6 A max (switch ratings apply), maximum suspended length approx. 45 m free-hanging cable. The cable is 10 m only; no other lengths are available. Blue to brown closes and blue to black opens as the liquid level rises.
Kemudahan Servis
KP dapat dibongkar untuk dibersihkan bila diperlukan. Rakitan probe pengganti tersedia dari Kelco Engineering atau distributor Anda.




