Seri MF20Sakelar Aliran Mikro

Versi super-sensitif dari sakelar aliran inline P20 yang populer: mendeteksi aliran di bawah 350 mL/jam. Murni mekanis, digerakkan secara magnetik, tanpa bagian logam yang bersentuhan dengan cairan; ideal untuk memantau pompa dosing bahan kimia, pengolahan air, menara pendingin, dan proses industri aliran rendah lainnya.

Seri MF20

Fitur

  • Mendeteksi aliran kurang dari 350 mL/jam
  • Cocok untuk tabung berdiameter 6 hingga 20 mm (1/4" hingga 3/4")
  • Tanpa bagian logam yang bersentuhan dengan cairan
  • Cocok untuk aliran berdenyut atau kontinu
  • Tekanan nominal 18 bar (260 psi)
  • Respons listrik yang stabil
  • Kemampuan aliran lewat yang sangat tinggi
  • Kehilangan head yang sangat rendah
  • Hanya untuk pemasangan vertikal
  • Mudah dipasang
  • Enklosur listrik tahan cuaca IP67
  • Rentang pH cairan 1 hingga 14

Bodi MF20 memuat piston beralur. Aliran apa pun (berdenyut atau kontinu) mengangkat piston ke atas dalam bodi sakelar hingga cairan melewatinya dan keluar dari bagian atas. Piston berisi magnet yang menggerakkan sakelar reed eksternal melalui bodi polipropilena: sistem balik gravitasi sederhana yang sangat andal dan tahan korosi. Tiga piston dipasok bersama setiap MF20 (ditandai A, B, C) yang mencakup titik penyakelaran dari 0.32 L/h hingga 12.8 L/h. MF20 dibuat dari polipropilena berpenguat kaca dengan seal O-ring Viton dan spigot PVC, yang merupakan satu-satunya material yang bersentuhan dengan cairan. Dipasok dengan fitting flare tabung untuk 3 ukuran tabung yang umum (tabung fleksibel 6 x 4, 8 x 4, dan 12 x 9) serta satu set union ¾" dan spigot pipa untuk pemasangan langsung pada perpipaan PVC atau ABS 15 NB.

Informasi Lainnya

Lembar data lokal belum tersedia untuk produk ini dalam bahasa yang Anda pilih. Tautan di bawah membuka versi bahasa Inggris.

Pilih Model

Pemesanan: Model yang Tersedia

Nomor ModelDeskripsi
MF20-BDry reed switch S.P.S.T. N.O. — 50 W/VA, 250 V AC / 200 V DC, 1.5 A max. Not suitable for inductive loads. PLC and general control circuits.
MF20-CDry reed switch S.P.D.T. break before make — 20 W/VA, 140 V AC / 150 V DC, 1 A max. Not suitable for inductive loads. PLC and general control circuits. Less sensitive than B/R — the flow needed to switch on and off is twice the piston values (multiply the switching flow rates by 2.0).
MF20-RSolid state relay (triac) S.P.S.T. N.O. — 740 W, 12 to 240 V AC, 4 A continuous (spike to 15 A); inductive loads 4 A at 240 V AC. AC control circuits and AC motor control.

Batas Operasi

Maximum recommended operating pressure (static or dynamic, ambient)1800 kPa / 260 psi
Minimum burst pressure (ambient)9700 kPa / 1400 psi
Maximum liquid temperature80 °C at 1 bar absolute (de-rate pressure linearly with temperature — see note)
Minimum liquid temperature-30 °C
Maximum recommended continuous flow (water)25 L/min (head loss across the switch < 100 kPa at 25 L/min)
Liquid pH range1 to 14
Ingress protection ratingIP67
Flow sensitivity — piston A (default)0.32 L/h rising / 0.30 L/h falling (±10%); response time 4 s
Flow sensitivity — piston B (supplied)3.10 L/h rising / 3.05 L/h falling (±10%); response time 3 s
Flow sensitivity — piston C (supplied)12.8 L/h rising / 12.6 L/h falling (±10%); response time 2 s
Flow sensitivity — MF20-CLess sensitive: for any given piston, multiply the switching flow rates above by 2.0. The A, B and C values above are for the MF20-B and MF20-R.
Flow sensitivity test basisWater at 15 °C, accurate to ±10%. Changes in liquid viscosity or temperature affect the switching point: higher viscosity lowers the flow needed to actuate the switch and lengthens the response time; lower viscosity does the opposite.

Dimensi

Dimensi Seri MF20
Vertical mount — 152 mm tall × 50 mm × 85 mm housing. Inlet at bottom, outlet at top; 3/4" BSP unions both ends, 15 N/B PVC pipe tails (solvent glue), M20 cable gland.

Warning: Electrical Safety

The MF20 Series flow switch is a mains voltage device. Death or serious injury may result if this switch is not correctly installed and operated. All electrical work on this switch must be performed by a fully qualified and licensed electrician.

Vertical Mounting Required

The MF20 must be mounted vertically with flow upward through the body. Gravity returns the piston to the off position when flow stops. There is a direction of flow arrow on the switch body — the switch will not operate against a reversed flow. The switch can be mounted directly on the suction or discharge valve of a metering pump.

Three Switch Points (Pistons A/B/C)

Three pistons ship with every MF20, each with an accurate and predictable switch point. The ‘A’ piston is fitted as standard (most sensitive); the ‘B’ and ‘C’ pistons are packed in the box. Switch points span 0.32 L/h to 12.8 L/h (MF20-B and MF20-R; the MF20-C needs twice the flow). The piston is changed by unscrewing the inlet adaptor (part No. 2) and inserting the new piston. The spanner octagon on the inlet adaptor accepts a standard gas cylinder spanner (28 mm across the flats).

Pulsed-Flow Behaviour

In pulsed-flow applications without a pulse dampener, if the pulse frequency is less than the electrical response time the MF20 may respond with a train of on/off pulses rather than a continuous on signal. Add a small in-line dampener if a steady output is needed.

Chemical Compatibility — DO NOT USE WITH

The MF20 wetted parts are glass-reinforced polypropylene with Viton O-ring seals (and PVC spigots). NEVER use this switch with: (1) sodium hypochlorite > 10% concentration; (2) ferrous or ferric solutions (e.g. ferric chloride); (3) solvents, hydrocarbons or alcohol solutions of any kind; (4) sulphuric acid > 50% concentration; (5) nitric acid > 20% concentration. For other media, use our Chemical Compatibility tool, widely available chemical compatibility charts for polypropylene and Viton, or ask Kelco.

Open Chemical Compatibility →

Pressure De-rating at Elevated Temperatures

The 1800 kPa max operating pressure applies at 15 °C. Maximum operating pressure must be de-rated linearly in direct proportion to temperature increase, to a maximum of 1 bar absolute at 80 °C. In other words, only use this switch at elevated temperatures in non-pressurised systems that are totally open to atmosphere in all circumstances and under all conditions.

Clean Fluid & Line Filtration

The MF20 contains a close fitting piston and should only be used where the process fluid is reasonably clean and free of entrained or suspended material. Fluids containing large particulate matter, ferrous materials or fibrous matter should not be used in this switch. If the degree of contamination of the process fluid can’t be guaranteed, fit suitable line filtration upstream of the MF20.

Pipe & Tube Connections

The MF20 is terminated with ¾" BSPP male threads, which can be screwed directly into pipe sockets and used in ¾" piping. It is also supplied with ¾" unions and ½" (15 NB) PVC spigots — thick walled, designed to be tapped ¼" BSP for compression fittings if required, and suitable for solvent gluing directly into 15 NB PVC or ABS pipe fittings — plus 3 sets of tube flare fittings to suit 6 by 4, 8 by 4 and 12 by 9 flexible tube.

Reed Switch Protection

The MF20 uses reed switches as the primary switching element. They offer an operating life in excess of 100 million cycles but must not be electrically overloaded. Where the reed switch is the main switch, use interposing relays and avoid inductive loads, and fit suitable protection such as diodes or rate effect suppression circuits. Avoid capacitive coupling effects on long cable runs by using shielded cable, and fit diode protection to the reed switches in DC applications.

Typical Applications

Control for backup dosing pumps, chemical metering pump control, chemical injection point status, laboratory applications, loss of prime detection and batch control.

Hazardous Areas

The MF20-B and MF20-C are simple apparatus under AS/NZS 60079.11 and may be used in a hazardous area only as part of an intrinsically safe circuit, connected through suitably certified associated apparatus. They are not Ex certified in their own right. The full conditions of use are given in the installation sheet. The MF20-R is not certified for use in hazardous areas and must not be installed in any area classified as hazardous under AS/NZS 60079.10 (Zone 0, 1, 2, 20, 21 or 22).

Kemudahan Servis

Sepenuhnya dapat diservis di lapangan. Papan sirkuit listrik dapat dipertukarkan; kit suku cadang tersedia untuk sebagian besar komponen, dan semua komponen sakelar tersedia sebagai suku cadang, termasuk ketiga piston (A/B/C) dan seal O-ring. Tersedia dari Kelco Engineering atau distributor Anda.

Lainnya di Sakelar aliran inline