IPG20 MK3Pelindung Pompa Cerdas

Dirancang untuk sistem irigasi air tawar maupun efluen. Mempelajari tekanan operasi setiap kali sistem dihidupkan, lalu menerapkan set point tekanan rendah dan tekanan lebih sendiri untuk deteksi kebocoran dan tekanan lebih yang sangat tepat sasaran. Cocok untuk pod tetap maupun irigator berjalan.

IPG20 MK3

Fitur

  • Mempelajari tekanan operasi
  • Sistem irigasi tetap atau berjalan
  • Mengompensasi perubahan kontur tanah
  • Operasi siklik untuk sistem pod
  • Deteksi kebocoran dan penyumbatan
  • Proteksi hilangnya aliran
  • Menampilkan tekanan dan set point
  • Tekanan nominal 20 bar / 2000 kPa
  • Operasi multi-tegangan
  • Operasi manual atau otomatis
  • Peringkat IP64

Pelindung pompa cerdas IPG20 MK3 berkonstruksi termoplastik dengan sambungan proses 1" BSP. Dipasok dengan satu paddle yang sesuai untuk pipa berukuran 25 mm ke atas, ditambah dua kawat (trailing wire) yang sesuai untuk pipa berdiameter dalam 65 mm – 100 mm (tergantung kecepatan aliran).

Pilih Model

Pemesanan: Model yang Tersedia

Nomor ModelDeskripsi
IPG20-MK3Standard model — 220–240 V AC and 24 V AC or 24 V DC operation
IPG20-12-MK3Low-voltage model — 12 V DC operation only

Batas Operasi

Ambient temperature range1 °C to 50 °C
Liquid temperature range1 °C to 60 °C
Ingress protection ratingIP64
Maximum operating pressure (static or dynamic)20 bar / 2000 kPa
Minimum burst pressure> 30 bar / 3000 kPa
Starting pressure range0–2000 kPa in 1 kPa steps
Stopping pressure range0–2000 kPa in 1 kPa steps
Minimum pressure differential1 kPa
Recommended pipe size25 mm / 1" or larger (no upper limit)

Data Listrik

Supply voltage220–250 V AC or 18–25 V AC/DC (multi-voltage input)
Maximum motor loadSingle-phase motors up to 2.4 kW max at 240 V AC (P1). 3-phase motors of all sizes via a suitable interposing contactor — no maximum motor size applies.
Relay 1 contact rating16 A at 240 V AC resistive
Relay 2 contact rating16 A at 240 V AC resistive

Fungsi

# = dapat diatur pengguna

#Manual or Automatic operation—
#Auto terrain compensationAllows for contour change with a travelling irrigator.
#Drift allowance (kPa)Auto terrain compensation only.
#Pre-start delay timerAdjustable from 1 second to 27.7 hours in 1-second increments.
#Use alarm relay—
#Absolute low pressureDetects a major leak during start-up.
#Low pressure marginFine leak detection.
#Absolute high pressureClosed-valve protection.
#High pressure marginPartial blockage detection.
#Set-point marginAllowable pressure variation during the learning process.
#Ramp-up timerAllows time to establish stable pressure. 1 second to 15 minutes in 1-second increments.
#Set-point timerAdjustable in 60-second increments.
#Pressure dip timerAdjustable from 1 second to 4 minutes in 1-second increments.
#Pressure spike timer—
#Run-on timer (loss of flow)Adjustable from 1 second to 15 minutes in 1-second increments.
#Cyclic runningRunning and stopping times both 2 minutes to 99 hours 59 minutes in 1-minute increments. Not available in auto-terrain-compensation mode.
#Auto restart on a faultAdjustable 1 minute to 99 hours 59 minutes. Not available in auto-terrain-compensation mode.
#Program lock—
Pressure / set-point displayDisplays system pressure and high & low pressure set points in kPa.
Pump run-time displayDisplays the total time the pump ran in minutes.
Fault diagnostic displayDisplays the reason for stopping on a fault.
Remote learningInstigate the learning process using a remote switch (manual operation).
No-flow protectionNo-flow protection at all times.

Dimensi

Dimensi IPG20 MK3
Three views with key dimensions (mm). 1" BSPT thread connection; paddle is cut to suit application; three M20 cable glands; removable protective cap.

Self-Learning Pressure Algorithm

The IPG20 MK3 measures the system’s normal operating pressure each time it starts and uses that as the reference for under- and over-pressure detection. As the irrigator travels over varying terrain the auto-terrain-compensation function adjusts the reference downward / upward in real time, so leak and blockage thresholds remain meaningful even as system pressure changes naturally.

Flow Sensitivity & Paddle Trimming

The IPG20 ships with one paddle (suits pipes 25 mm and larger) and two trailing wires (suits 65–100 mm ID, subject to velocity). The flow at which the paddle activates depends on pipe size, viscosity, and trimmed paddle length. Use the online Paddle Calculator to estimate activation flow and determine how much to trim the paddle for your application.

Open the Paddle Calculator →

3-Phase Pump Motors

The IPG20 MK3 can be used to control either single-phase or 3-phase pumps, provided a 220–240 V AC or 24 V AC/DC supply is available at the installation site. For 3-phase motors the IPG20 drives an interposing contactor — use the Pump Controller Power Calculator to size the contactor and verify cable rating + voltage drop.

Open the Pump Controller Power Calculator →

Application Restriction

The IPG20 MK3 is an industrial control device, specifically designed for use in dairy and agricultural applications. It must never be used for any other application. Installation must be carried out by a qualified pump engineer, and all electrical work by a licensed electrician.

Hazardous Areas

The IPG20 MK3 is not certified for use in hazardous areas and must not be installed in any area classified as hazardous under AS/NZS 60079.10 (Zone 0, 1, 2, 20, 21 or 22).

Kemudahan Servis

Pelindung pompa cerdas IPG20 MK3 tidak dapat diservis oleh pengguna. Namun, suku cadang tersedia dari Kelco Engineering atau distributor Anda.

Lainnya di Pengendali pompa