F60 MK3Pengendali Pompa Digital

Pengendalian pompa yang paling serbaguna dan fleksibel, mudah digunakan dan sangat bertenaga. Memantau tekanan dan aliran sistem untuk memastikan perlindungan pompa yang menyeluruh, dengan lima mode operasi untuk sistem satu atau dua pompa.

F60 MK3

Fitur

  • Sangat mudah diprogram
  • Operasi multi-tegangan
  • Menampilkan tekanan dan set point
  • 15 timer terprogram bawaan
  • Penggerak solid-state 40 A yang bertenaga
  • Relai alarm khusus
  • Enklosur listrik yang dapat dilepas
  • Tekanan nominal 20 bar (290 psi)
  • Cocok untuk pipa 25 mm (1") dan lebih besar
  • Menerima input jarak jauh
  • Bodi tahan cuaca

Pengendali Pompa Digital F60 MK3 tersedia dalam konstruksi termoplastik penuh dengan sambungan proses 1" BSP. Pengendali standar beroperasi dari 220–240 V AC atau 24 V AC/DC; tersedia juga model khusus 12 V DC.

Opsi tipe kawat (trailing wire)

Pengendali ini dapat menggunakan kawat (trailing wire) sebagai pengganti paddle. Pesan F60-MK3 / F60-MK3-12 bersama kit lengan kawat Seri TW (TW-ARM-KIT-[length]): keduanya adalah dua item terpisah.

Kit dikirim dalam keadaan terpisah (belum terpasang) dan dipasang oleh instalatur Anda. Kelco tidak memasang kit dan tidak menyediakan unit yang sudah terpasang. Petunjuk pemasangan dikirim melalui email bersama penawaran harga Anda.

Panjang kit: 50, 80, 100, 140, 160, 180, 200, 250 dan 300 mm. Untuk panjang lainnya, silakan kirim email ke [email protected].

Temukan kit di Suku Cadang. Periksa panjang untuk pipa Anda di Kalkulator Pemotongan Paddle.

Pilih Model

Pemesanan: Model yang Tersedia

Nomor ModelDeskripsi
F60-MK3Standard model — 220–240 V AC and 24 V AC or 24 V DC operation
F60-MK3-12Low-voltage model — 12 V DC operation only

Batas Operasi

Ambient temperature range1 °C to 50 °C
Liquid temperature range1 °C to 60 °C
Ingress protection ratingIP64
Maximum operating pressure (static or dynamic)20 bar / 290 psi
Minimum burst pressure> 25 bar / 360 psi
Starting pressure range0 to 2000 kPa or 0 to 290 psi in steps of 1 kPa or 1 psi
Stopping pressure range0 to 2000 kPa or 0 to 290 psi in steps of 1 kPa or 1 psi
Minimum pressure differential (on-to-off, off-to-on)1 kPa or 1 psi
Recommended pipe size25 mm / 1" or larger (no upper limit)

Data Listrik

Supply voltage (standard model)220–250 V AC or 18–25 V AC/DC (multi-voltage input)
Supply voltage (12 V DC model)11–14 V DC (65 mA current draw)
Maximum motor load (all models)Single-phase motors up to 2.4 kW max at 240 V AC (P1). 3-phase motors of all sizes via a suitable interposing contactor — no maximum motor size applies when using an interposing contactor.
Relay 1 normally-open contact rating (HD terminal not in use)10 A at 240 V AC resistive
Relay 1 normally-closed contact rating3.5 A at 240 V AC resistive
Relay 2 normally-open contacts3.5 A at 240 V AC resistive

Fungsi

# = dapat diatur pengguna

#Select pressure units (kPa or psi)—
#Pre-start delay timerAll modes. Adjustable from 1 second to 18 hours in 1-second increments.
#Start-up timerAll modes. Adjustable from 1 second to 15 minutes in 1-second increments.
#Pressure rise timerMode 4 only. Allows time for the pressure to rise. Adjustable from 1 second to 15 minutes in 1-second increments.
#Run-on timerAll modes. Adjustable from 1 second to 15 minutes in 1-second increments.
#Pressure dip timerMode 4 only. Adjustable from 1 second to 4 minutes in 1-second increments.
#Delayed restarting timerModes 1–3 only. Adjustable from 1 minute to 99 hours 59 minutes in 1-minute increments.
#Starting pressure0 to 2000 kPa or 0 to 290 psi in 1 kPa or 1 psi steps.
#Stopping pressure0 to 2000 kPa or 0 to 290 psi in 1 kPa or 1 psi steps.
#Cyclic running and stopping timersAll modes. Running and stopping times both adjustable from 2 minutes to 99 hours 59 minutes in 1-minute increments.
#Auto restart if run dryAll modes. Single or repeatable tries. Adjustable from 1 minute to 99 hours 59 minutes in 1-minute increments.
#Anti-cyclingModes 1–3 only. Adjustable from 1 motor start per hour to 1800 motor starts per hour.
#Burst pipe detectionMode 3 only. Adjustable from 1 minute to 99 hours 59 minutes in 1-minute increments.
#Leak detector—
#Dual pump control with or without dual flow sensing—
#Starts the pump at a preset low pressure—
#Stops the pump at a preset high pressure—
Stops the pump if flow stopsLoss-of-prime protection for the pump(s).
Displays system pressure in preferred units—
Displays high & low pressure set points—
Remote startCan start the pump using an external switch.
Flow-only start/stopStarts and stops the pump on flow regardless of pressure.
Pump run-time displayDisplays the total time the pump ran in minutes.
Fault diagnostic displayOn a fault, displays the reason the pump was shut down.
Remote stopRemote stop via an external switch opening its contacts — stops the pump if flow stops.

Dimensi

Dimensi F60 MK3
Three views with key dimensions (mm). 1" BSPT thread connection; paddle is cut to suit application; three M20 cable glands; removable protective cap.

5 Operating Modes

The F60 MK3 includes 5 unique operating modes, each combining a different subset of the available timers and pressure-control functions. Different modes suit pressure-only, flow-only, dual-sensor, and dual-pump scenarios. The full mode × function matrix is set out in the printed data sheet PDF available below.

Flow Sensitivity & Paddle Trimming

Like the F29, the F60 MK3 uses a mechanical paddle to detect flow. The flow rate at which the paddle activates depends on pipe size, fluid viscosity, turbulence, and the trimmed paddle length. For an accurate estimate of activation flow and to determine how much to trim the paddle for your application, use the online Paddle Calculator.

Open the Paddle Calculator →

3-Phase Pump Motors

The F60 MK3 can be used to control either single-phase or 3-phase pumps, provided a 220–240 V AC or 24 V AC supply is available at the installation site. For 3-phase motors the F60 drives an interposing contactor — use the Pump Controller Power Calculator to size the contactor and verify cable rating and voltage drop.

Open the Pump Controller Power Calculator →

Hazardous Areas

The F60 MK3 is not certified for use in hazardous areas and must not be installed in any area classified as hazardous under AS/NZS 60079.10 (Zone 0, 1, 2, 20, 21 or 22).

Kemudahan Servis

Pengendali pompa digital F60 MK3 tidak dapat diservis oleh pengguna. Namun, suku cadang tersedia dari Kelco Engineering atau distributor Anda.

Lainnya di Pengendali pompa