Seri FSakelar Aliran Tipe Paddle Tahan Korosi
Sakelar paddle yang tangguh dan sangat sensitif untuk cairan panas maupun dingin. Penggerak tolakan magnetik (tanpa seal, diafragma, atau bellow) menghasilkan sakelar tekanan tinggi tanpa titik potensi kegagalan. Sambungan proses polipropilena atau baja tahan karat 316; 3/4" atau 1" BSP/NPT.

Fitur
- Sakelar S.P.D.T. 5–500 V AC, 15 A (model F-H)
- Tersedia model 'L' kontak emas tegangan rendah (F-L)
- Model polipropilena atau baja tahan karat 316
- Tersedia sakelar dengan ulir BSP & NPT 3/4" dan 1"
- Pengesampingan manual bawaan (model F-H dan F-L)
- Konstruksi modular: lepaskan enklosur, atau ulir lepas sakelar dari pipa, tanpa mengganggu pengkabelan
- Tersedia model tekanan tinggi 400 bar / 5800 psi (baja tahan karat)
- Penggerak magnetik tanpa seal
- Bodi IP67 tahan cuaca
- Mudah diservis
Enklosur listrik adalah rakitan terpisah yang terkunci pada bagian basah dengan satu sekrup yang dapat dijangkau dari luar, sehingga dapat dilepas untuk servis, atau sakelar dapat diulir lepas dari pipa, tanpa mengganggu pengkabelan. Setiap sakelar Seri F dipasok dengan paddle polipropilena berpenguat serat kaca yang dapat dipotong dan dibentuk agar sesuai dengan pipa 25 mm (1") dan lebih besar. Pengesampingan manual bawaan menyalakan unit hanya dengan menekan tombol, terlepas dari ada tidaknya aliran, sehingga pompa dapat dihidupkan secara manual kapan saja dan pengujian serta komisioning menjadi mudah. Tersedia dengan sambungan proses polipropilena atau baja tahan karat 316 tekanan tinggi, dengan model yang sesuai untuk sebagian besar aplikasi, termasuk air laut, air sumur bor, asam, basa, dan banyak larutan kimia.
Informasi Lainnya
Lembar data lokal belum tersedia untuk produk ini dalam bahasa yang Anda pilih. Tautan di bawah membuka versi bahasa Inggris.
- Lembar Data Seri F
- Lembar Instalasi F-H Series
- Lembar Instalasi F-L Series (tegangan rendah)
- Dipasang pada standoff? Pemeriksaan standoff
Model CAD 3D (6 model, STEP)
Model eksternal yang disederhanakan untuk tata letak dan pemasangan; bukan untuk manufaktur.
- F-H-25B8.6 MB
- F-H-25B-SS7.2 MB
- F-H-25N8.3 MB
- F-L-25B8.6 MB
- F-L-25B-SS7.2 MB
- F-L-25N8.3 MB
Cara paddle Seri F merespons aliran
Pemesanan: Model yang Tersedia
Batas Operasi
Data Listrik
Dimensi

Manual Override (F-H and F-L models)
All F-H and F-L models include a red manual override button on the side of the housing, under the cable gland. Pressing the button switches the flow switch on regardless of flow — useful for manually starting pumps in spite of an initial lack of flow, and for testing/commissioning of control circuits. After wiring, press it to test: the switch changes state as if liquid were pushing the paddle.
Flow Sensitivity & Paddle Trimming
The flow rate needed to actuate the F Series depends on many variables — turbulence, liquid viscosity and the exact area of the paddle face exposed to flow. Trim the paddle with a hacksaw or tin snips so it clears the pipe wall by at least 4 mm all round. As a guide: low flow — paddle just clears the bottom of the pipe; unknown flow — 3/4 of the way across the pipe; high flow — 1/4 to 1/2 of the way across the pipe. Spare paddles are available if too much is cut off. For an accurate estimate of switch performance and to determine the effect of paddle trimming, use the online Paddle Calculator — enter your pipe inside diameter, flow rate and liquid.
Sensitivity Adjustment
F-H and F-L switches are supplied at maximum sensitivity (adjuster wound fully in). To decrease sensitivity, remove the red dust cap and wind the adjusting screw out (anticlockwise) with a wide flat screwdriver. The further out the screw, the more flow is needed to operate the switch. Refit the dust cap.
Mounting
The switch can go in suction or delivery pipework, horizontal or vertical. In vertical pipe the flow must be upward. Do not mount on the underside of horizontal pipe. Where possible, mount the switch away from pumps, valves and bends — a fitting directly upstream makes the flow uneven and turbulent at the paddle, which can shift the switching point slightly or make the paddle flutter near the switching point; downstream fittings have little effect. Mount in a pipe tee, tapping saddle or weld-on socket, square to the flow so liquid hits the flat face of the paddle, with the arrow on the switch pointing in the direction of flow. Seal the thread with PTFE tape or thread sealant, leaving at least 4 mm of thread above the socket, and tighten with a spanner on the spanner flats only — never twist the switch body.
Electrical Installation
The F Series is a mains voltage device — all electrical work must be carried out by a licensed electrician. Terminals are marked C (common), NO (normally open) and NC (normally closed); for a two-wire connection use C plus either NO or NC to suit the application. After wiring, fully tighten the cable gland nut, check the lid gasket is in place and tighten the lid down. Without its lid the switch is not water, weather or insect proof and presents a shock hazard.
Hazardous Areas
The F-H is not certified for use in hazardous areas and must not be installed in any area classified as hazardous under AS/NZS 60079.10 (Zone 0, 1, 2, 20, 21 or 22). The F-L is simple apparatus under AS/NZS 60079.11 and may be used in a hazardous area only as part of an intrinsically safe circuit, connected through suitably certified associated apparatus. It is not Ex certified in its own right. The associated apparatus must not exceed Uo ≤ 30 V, Io ≤ 100 mA. The full conditions of use are given in the installation sheet.
F-L — Inductive and Capacitive Loads NOT Suitable
The F-L is not suitable for inductive or capacitive loads such as contactors and relays. Loads above the rating will damage the switch.
Reed Switch — Inductive Loads NOT Suitable
The F-RL reed switch must NOT be used with inductive loads such as contactors or high-wattage relays. Use the F-H model or interpose a relay/contactor for such applications.
Materials & Chemical Compatibility
All-polypropylene models (no suffix) have polypropylene wetted parts. The -SS models have a high-pressure 316 stainless steel process connection and a polypropylene paddle. The paddle on every F Series model is glass-fibre-reinforced polypropylene. Check that the switch materials suit the liquid being monitored.
20 mm models stainless only
20 mm (3/4") fittings are only available with the 316 stainless steel process connection — not available in all-polypropylene.
Approved Standards
The 'H' and 'L' microswitches used in the F Series are approved to UL1054 (File E41515), CSA C22.2 No.55 (File LR21642) and EN61058-1, and are CE marked.
Kemudahan Servis
Sepenuhnya dapat diservis di lapangan. Satu sekrup yang dapat dijangkau dari luar melepas enklosur listrik dari bagian basah: lepaskan untuk servis, atau ulir lepas sakelar dari pipa, tanpa mengganggu pengkabelan. Paddle, seal, dan sakelar pengganti tersedia dari Kelco Engineering atau distributor Anda.

